Steklo i Keramika (Glass and Ceramics). Monthly scientific, technical and industrial journal

 

ISSN 0131-9582 (Online)

Development of an Organic Binder for Ceramic Products Obtained by the Additive Technology Method

Details
Hits: 5668
Autors: Poilov V. Z., Punkaev V. V., Kalugina K. E., Cherepanova M. V., Ouglev N. P.
  • Continuous numbering: 1111
  • Pages: 3-7
  • Share:

Heading: Not-set

When using almost all types of additive technologies, it is mandatory to use a binder with further heat treatment of the finished product. The binder compositions can be very diverse. Correct selection of the composition and properties of the ceramic powder - binder system at all stages of the process allows creating high-performance installations for producing parts of complex shapes. Presented are studies on the development of a binder composition for oxide aluminum-zirconium powders
Dr. Tech. V.Z.POILOV ( e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it. ), V.V. PUNKAEV ( e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it. ), K. E. KALUGINA ( e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it. ), Cand. tech. Sciences M. V. CHEREPANOVA ( e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it. ), Cand. chem. N. P. UGLEV ( e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it. ); Perm National Research Polytechnic University (PNRPU) (Russia, Perm)
Litunov S.N., Slobodenyuk V.S., Melnikov D.V. Review and analysis of additive technologies. Part 1 // Omsk Scientific Bulletin. 2016.? 1 (145). S. 12? 17. Romanov MK, Zhuravleva LI Analysis of the technological and economic feasibility of using additive technologies in the manufacture of ceramic parts. Glass and Ceramics. 2019.? 9, p. 9? 16. ? Romanov MK, Zhuravleva LI Analysis of the Technological and Economic Expediency of Using Additive Technologies in Manufacturing Ceramic Parts // Glass Ceram. 2019. V. 76. No. nine ? 10.P. 328? 333.? Pat. 2663768 RF. Method of manufacturing filtering membranes using additive technology and the resulting membranes / F. Lekos, J. Anketiy. ? 2015156338; application form 10.06.2014; publ. 08/09/2018 // Bul. 2018.? 22. Pat. 2621764 RF. Liquid binding composition for joining fibrous materials / K. L. Restuccia, W. Jacobs. ? 2015129529; declared 08/29/2013; publ. 01/25/2017 // Bul. 2017.? 3. Pat. 2671337 RF. Method and device for additive mechanical build-up of tubular structures / K. Tyler. ? 2018106913; declared 07/19/2016; publ. 30.10.2018 // Bul. 2018.? 31. Uglev NP, Poilov VZ, Dyakov MS, Novokreshchennykh EN Development of an express method for determining the mechanical strength of casting ceramics // International research journal. 2017.? 11. Uglev NP, Poilov VZ, Karmanov VV et al. Influence of technological parameters of raw materials on the physical and mechanical characteristics of ceramics. Glass and ceramics. 2016.? 6.S. 15? 21. ? Uglev NP, Poilov VZ, Karmanov VV et al. Effect of Technological Parameters of Raw Materials on the Physical? Mechanical Characteristics of Ceramics. 2016. V. 73. No. 5? 6. P. 213? 218.?

The article can be purchased
electronic!

PDF format

700 руб

UDK 666.3.022:66.7:621.74.045:669.24/.29
Article type: Not-set
Make a request

Keywords

powder materials, binder, 3D printer, ceramics, aluminum oxide, zirconium oxide

Use the reference below to cite the publication

Poilov V. Z., Punkaev V. V., Kalugina K. E., Cherepanova M. V., Ouglev N. P. Development of an Organic Binder for Ceramic Products Obtained by the Additive Technology Method. Steklo i keramika. 2020:93(7):3-7. (in Russ). UDK 666.3.022:66.7:621.74.045:669.24/.29
Баннер снизу

Editor-in-chief

Lyudmila Vladimirovna Sokolova