Refractory and heat-resistant materials with a coarse-grained and large-porous structure were obtained using silica glass suspensions with mullite, spinel, corundum and quartz fillers. The influence of sintering temperature on the phase composition, structure, porosity and density of the materials were studied. It was found that the strength of the ceramics increases in the temperature range 1300…1400 ?C and decreases at 1500…1600 ?C due to the crystallization of the silica glass. The composites in the silica glass–corundum system have the most stable strength characteristics.
Sharif M. Sharafeev – Candidate of Technical Sciences, Junior Researcher, The Kizhner Research Center, School of Advanced Manufacturing Technologies, National Research Tomsk Polytechnic University, Tomsk, Russia.E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it..
Olga V. Kazmina – Doctor of Technical Sciences, Professor, The Kizhner Research Center, School of Advanced Manufacturing Technologies, National Research Tomsk Polytechnic University, Tomsk, Russia.E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Alexander V. Gubanov – Engineer, The Kizhner Research Center, School of Advanced Manufacturing Technologies, National Research Tomsk Polytechnic University, Tomsk, Russia. E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Viktor A. Kutugin – Candidate of Technical Sciences, Associate Professor, The Kizhner Research Center, School of Advanced Manufacturing Technologies, National Research Tomsk Polytechnic University, Tomsk, Russia. E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Gleb V. Polushin – Master’s Student, The Kizhner Research Center, School of Advanced Manufacturing Technologies, National Research Tomsk Polytechnic University, Tomsk, Russia. E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
1. Revelo C., Colorado H. 3D printing of kaolinite clay ceramics using the direct ink writing (DIW) technique // Ceram. Int. 2018. V. 44, No. 5. P. 5673 – 5682. DOI: 10.1016/j.ceramint.2017.12.219
2. Shahzad A., Lazoglu I. Direct ink writing (DIW) of structural and functional ceramics: recent achievements and future challenges // Compos. Part B Eng. 2021. V. 225. P. 109249. DOI: 10.1016/j.compositesb.2021.109249
3. Rueschhoff L., Costakis W., Michie M., et al. Additive manufacturing of dense ceramic parts via direct ink writing of aqueous alumina suspensions // Int. J. Appl. Ceram. Technol. 2016. V. 13, No. 5. P. 821 – 830. DOI: 10.1111/ijac.12557
4. Guzi de Moraes E., Ferreira I., Teixeira L., et al. Additive manufacturing of cellular structures from recycled soda-lime glass printing inks by robocasting // Ceram. Int. 2023. V. 49, No. 4. P. 6554 – 6562. DOI: 10.1016/j.ceramint.2022.10.270
5. Gutierrez L., Pawlik M. Influence of pH and temperature on the rheology of aqueous quartz-bitumen suspensions // J. Rheol. 2012. V. 56, No. 4. P. 687 – 706. DOI: 10.1122/1.4708340
6. M’Barki A., Bocquet L., Stevenson A. Linking rheology and printability for dense and strong ceramics by direct ink writing // Sci. Rep. 2017. V. 7, No. 1. P. 6017. DOI: 10.1038/s41598-017-6115-0
7. Sweeney M., Campbell L., Hanson J., et al. Characterizing the feasibility of processing wet granular materials to improve rheology for 3D printing // J. Mater. Sci. 2017. V. 52, No. 22. P. 13040 – 13053. DOI: 10.1007/s10853-017-1404-z
8. Panda B., Unluer C., Tan M. Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing // Cem. Concr. Compos. 2018. V. 94. P. 307 – 314. DOI: 10.1016/j.cemconcomp.2018.10.002
9. Barbara L., Ginebra M.-P. Rheological characterisation of ceramic inks for 3D direct ink writing: A review // J. Eur. Ceram. Soc. 2021. V. 41, No. 16. P. 18 – 33. DOI: 10.1016/j.jeurceramsoc.2021.08.031
10. Пивинский Ю. Е., Ромашин А. Г. Кварцевая керамика. М.: Изд-во «Металлургия», 1974. 265 с.
11. Kharitonov D. V., Makarov N. A., Anashkina A. A., Motornova M. S. Effect of highly disperse SiO2 particles on the sintering of quartz ceramic: firing regime choice for quartz ceramic articles and the colloidal component concept // Glass Ceram. 2018. V. 75, No. 5–6. P. 190 – 194. DOI: 10.1007/s10717-018-0053-2
12. Пивинский Ю. Е. Бесцементные огнеупорные бетоны. Часть 1. Общие сведения. ВКВС и керамобетоны // Новые огнеупоры. 2019. № 9. С. 14 – 24.
13. Пивинский Ю. Е., Дякин Д. В. Бесцементные огнеупорные бетоны. Часть 8. Особенности структуры, спекание и муллитизация высокоглиноземистых матричных систем // Новые огнеупоры. 2021. № 5. С. 113 – 125.
14. Дякин П. В., Пивинский Ю. Е., Прохоренков Д. С., Дороганов В. А. Фазовый состав, структура и некоторые свойства материалов на основе ВКВС боксита композиционного состава в системе Al2O3–SiO2–SiC // Вестник БГТУ. 2020. № 2. С. 115 – 125.
15. Пивинский Ю. Е., Гришпун Е. М., Гороховский А. М. Разработка технологий, производство и служба формованных и неформованных огнеупоров на основе ВКВС // Новые огнеупоры. 2016. № 5. С. 29 – 39.
16. Колобов А. Ю., Сычева Г. А. Особенности кристаллизации и свойств кварцевого стекла, полученного на плазмотронах ОАО «Динур» из кварцевого песка раменского месторождения // Физика и химия стекла. 2020. Т. 46, № 3. С. 281 – 290.
17. Pagliari L., Dappiaggi M., Pavese A., Francescon F. A kinetic study of the quartz-cristobalite phase transition // J. Eur. Ceram. Soc. 2013. V. 33, No. 15–16. P. 3403 – 3410. DOI: 10.1016/j.jeurceramsoc.2013.06.014
The article can be purchased
electronic!
PDF format
700 руб
DOI: 10.14489/glc.2024.01.pp.023-032
Article type:
Research Article
Make a request
