-
21.
RESEARCH OF THE DEPENDENCE OF THE THERMAL STRENGTH PROPERTIES OF REFRACTORY MATERIALS OF THE LADLE LINING OF THE FERROALLOY PRODUCTION ON TEMPERATURE
-
(Not-set)
-
The article is devoted to the study of the dependence of the change in compressive strength on temperature for refractory materials of the lining of a pouring ladle of ferroalloy production – fireclay ...
-
22.
ULTRA-SOFT X-RAY SPECTROSCOPY STUDY OF CHROMIUM-DOPED TITANIUM CALCIUM-COPPER CaCu3Ti4O12
-
(Not-set)
-
... from 7.3897 (х = 0.02) to 7.3866 ? (х = 0.06). Copper oxide was determined in the intergranular space in all samples. The samples were characterized by a low-porosity grain microstructure; with an increase ...
-
23.
PHYSICAL AND MECHANICAL PROPERTIES OF CERAMIC COMPOSITE MATERIAL BASED ON Al6Si2O13–ZrSiO4
-
(Not-set)
-
... of chemical elements. It was found that in all the studied samples two phases were formed – Al6Si2O13 and ZrSiO4. The porosity of the samples was determined and the dependence of this parameter on the ...
-
24.
PHASE FORMATION OF NEW PYROCHLORE TYPE CERAMICS Bi2.7Zn0.46Ni0.70Sb2O10 + ?
-
(Not-set)
-
... Phase-pure pyrochlore is formed at 950…1050 ?С. At a temperature of 1050 ?С, sintering of fine-grained ceramics occurs, a low-porosity microstructure is formed due to the fusion of small grains with the ...
-
25.
APPLICATION OF OIL SLUDGE AS A BURNOUT ADDITIVE IN FIRING OF ALMOSILICATE CERAMICS
-
(Not-set)
-
The possibility of using pyrolysis products of oil-containing waste, including oil sludge, in the synthesis of porous ceramics is shown. High carbon content in pyrolysis products of oil sludge determines ...
-
26.
THE INFLUENCE OF DIAMOND GRINDING MODES ON THE PHASE COMPOSITION AND CRACK RESISTANCE OF ZIRCONIA-BASED CERAMICS
-
(Not-set)
-
... surface of the samples, which leads to an increase in the critical stress intensity coefficient (K1c) from 4.3 to 6.4 MPa·m1/2. Mechanical processing of samples with an open porosity of 3.0…3.5 % obtained ...
-
27.
LASER THERMAL SEALING OF NANOPOROUS GLASSES
-
(Not-set)
-
The processes of thermal consolidation of nanoporous glass surface by means of carbon dioxide laser radiation have been investigated. Successful formation of a heat-sealed layer with a thickness of (20 ...
-
28.
LASER MODIFICATION OF GAS-THERMAL COATINGS SPRAYED BY HVOF – A REVIEW
-
(Not-set)
-
... of coatings, provides a higher density, reduces dispersion and porosity by 4 – 6 times, and allows you to adjust the distribution and value of residual stresses. It is shown that with the help of laser ...
-
29.
SYNTHESIS OF SILICON OXYCARBIDE COMPOSITE MODIFIED WITH TITANIUM OXIDE
-
(Not-set)
-
... to the plane reflections of anatase. The investigation of the IR spectra showed the presence of bands corresponding to vibrations of Ti–O–Ti and Ti–O–C bonds. The porosity of the synthesized samples was ...
-
30.
PREPARATION OF MESOPOROUS COMPOSITE TiO2-MONTMORILLONITE IN SOFT HYDROTHERMAL CONDITIONS
-
(Not-set)
-
In this work, mesoporous TiO2-montmorillonite composites with hydrothermally activated impregnation (115 °C, 0.5…5.0 h) of a mechanically and thermally activated support with titanium polyhydroxocomplexes ...
-
31.
SYNTHESIS OF Zn AND Mn CODOPED BISMUTH TANTALATE PYROCHLORE-TYPE CERAMICS
-
(Not-set)
-
... content of zinc ions in the samples from 10.4764(5) (x = 0.3) to 10.5122(5) ? (x = 0.7). According to electron scanning microscopy, ceramic samples are characterized by a low-porosity microstructure with ...
-
32.
PRODUCTION OF POROUS CERAMICS ?-Al2O3–3YSZ WITH ADDITIVE OF ?(?)-Al2O3
-
(Not-set)
-
... glycine or urea as fuels. After firing at 1550 ?C, the ceramics exhibited a closed porosity range of 14.1…24.0 %. The experimental results revealed a linear correlation between density and closed porosity ...
-
33.
OXIDATION OF Cr (III) TO Cr (VI) IN THE SYNTHESIS OF BISMUTH-CHROMIUM OXIDE CERAMICS
-
(Not-set)
-
Bismuth-containing chromates BixCrO1.5x+3 with a variable molar ratio of 1 ? n(Bi)/n(Cr) ? 38 were synthesized using
a ceramic method from Bi (III) and Cr (III) oxides. Depending on the n(Bi)/n(Cr) ratio, ...
-
34.
FABRICATION AND PROPERTIES OF CERAMICS/SINGLE CRYSTAL COMPOSITES BASED ON YTTRIUM ALUMINUM GARNET
-
(Not-set)
-
... was also examined. The most transparent samples were obtained at a temperature of 1850 °C. Microstructure studies of the composites revealed the presence of regular residual porosity near the interface, ...
-
35.
THERMAL INSULATION PROPERTIES OF CERAMOVERMICULITE AND KERAMOPERLITE MATERIALS ON A WOLLASTONITE BOND AT HIGH TEMPERATURE
-
(Not-set)
-
High-temperature thermal insulation materials are widely used in civil engineering as flame retardant materials, as well as in many industries. Rocks and industrial waste are used as raw materials for ...
-
36.
INFLUENCE OF REFRACTORY FILLERS ON THE PROPERTIES OF CERAMICS BASED ON HIGH CONCENTRATED SILICA GLASS SUSPENSIONS
-
(Not-set)
-
... sintering temperature on the phase composition, structure, porosity and density of the materials were studied. It was found that the strength of the ceramics increases in the temperature range 1300…1400 ...
-
37.
CHARACTERISTICS AND MORPHOLOGY OF THE PORE SPACE OF SYNTHETIZED HIGHLY POROUS Sc2O3 CERAMIC MATERIALS
-
(Not-set)
-
An energy-efficient synthesis of highly porous ceramic materials based on Sc2O3 was carried out using a combination of compaction and technological combustion methods with the participation of active binders. ...
-
38.
EFFECTS OF BINARY OXIDE COATED MWCNTS TOWARD TAILORING THE MECHANICAL, THERMO-MECHANICAL, AND MICROSTRUCTURAL PROPERTIES OF PRESSURELESS SINTERED MgAl2O4 SPINEL CERAMIC COMPOSITE
-
(Not-set)
-
... fabricated using a pressureless sintering technique. The physical properties, including porosity, bulk density, and flexural strength of spinel composites were evaluated in the temperature range of 1500 ...
-
39.
INTEGRATED APPROACH TO STUDYING CERAMIC ARTIFACTS IN KYRGYZSTAN
-
(Not-set)
-
The purpose of this article is to apply an integrated research approach for the reconstruction of ceramic production technology in the territory of the Kyrgyz Republic based on the results obtained by ...
-
40.
METHODS OF FORMING COMPLEX PROFILE PRODUCTS FROM HEAT-RESISTANT CERAMIC MATERIALS BASED ON SILICON CARBIDE
-
(Not-set)
-
... hot slip molding under pressure, has been studied. The obtained silicon carbide ceramic materials are characterized by a low density of about 3.04…3.07 g/cm3, a porosity of ? 1 % and a bending strength ...