-
1.
Study of the Porosity Structure of a Ceramic Material of the Fortress Wall of Girona (Spain)
-
(Not-set)
-
... indicates the introduction of fuel into the raw material. The increased content of fuel in the raw material contributes to the formation of porosity and uniform sintering inside the ceramic specimen. Integral ...
-
2.
Porosity Structure and Technical Properties of Ceramic Materials Based on Wastes of Nonferrous Metallurgy of Eastern Kazakhstan
-
(Not-set)
-
Clinker materials were obtained from non-ferrous metal waste, where the clay part of the tailings was used as the clay material. gravity of zircon-ilmenite ores (GZI), and feldspar concentrate (PShK) - ...
-
3.
Chemical, Phase Compositions and Structure of the Porosity of Bricks of the White Tower (Greece) is Older than 450 Years
-
(At the enterprises and institutes)
-
The increased carbon content (9.59 & # 37;) in the inclusions indicates the introduction of fuel into the raw material, which increases the porosity of the products and contributes to the uniform sintering ...
-
4.
Molding plasters in sanitaryware production. Adjusted porosity in terms of optimised strength
-
(Industrial experience)
-
The developed molding gypsum of improved quality is used in the casting of ceramic products using traditional and multiple casting technologies (Spagless). Such gypsums provide an increase in casting performance, ...
-
5.
Porosity and solubility of bioactive calcium-phosphate glassceramics for bone endoprosthesis
-
(Biomaterials)
-
The issues related to the solubility of glass-crystalline materials based on calcium phosphate glasses in water and solutions imitating the physiological environment of a living organism are considered. ...
-
6.
Gas-dynamic model of open and closed porosity formation in self-propagating high-temperature synthesis
-
(Science for ceramic production)
-
A gas-dynamic model of the formation of open and closed porosity of materials under the conditions of combustion of an SHS system, when there is a liquid phase (which can boil under certain conditions), ...
-
7.
Ceramic mass with a reduced porosity for decorative majolica
-
(Science for ceramic production)
-
Ceramic masses with low porosity have been developed on the basis of difficult-to-sinter clay from the Gzhel deposit and its mechanically activated part, as well as additives - nepheline-syenite and glass ...
-
8.
EFFECT OF TECHNOLOGICAL SYNTHESIS PARAMETERS ON THE STRUCTURE, PHASE COMPOSITION, AND PROPERTIES OF POROUS Al2O3–MgO–SiO2–SiC CERAMICS
-
(Not-set)
-
... in the compaction pressure from 20 to 40 MPa provides a twofold strengthening effect while maintaining high porosity, gas permeability, and structural homogeneity. The obtained results demonstrate the ...
-
9.
NANOSTRUCTURAL FEATURES OF HIGH-PRESSURE IMPACT-ORIGINATED MELT GLASS STUDIED BY SMALL-ANGLE SYNCHROTRON X-RAY SCATTERING
-
(Not-set)
-
Impact glasses are naturally occurring amorphous materials formed by high-velocity meteorite impacts on the Earth's surface. This paper examines the structural features of a high-pressure variety of impact ...
-
10.
INFLUENCE OF THE PURITY OF THE RAW MATERIALS SrCO3 AND TiO2 ON SOLID-STATE SYNTHESIS AND PROPERTIES OF SrTiO3 CERAMICS
-
(Not-set)
-
... in the case of samples with closed porosity reduces their relative density from 98 to 90 %, but does not significantly affect the dielectric characteristics. It has been found that the relative permittivity ...
-
11.
THE INFLUENCE OF SiC ADDITIVE ON THE FORMATION OF PHASE COMPOSITION AND MECHANICAL PROPERTIES OF Al2O3–ZrB2 CERAMIC COMPOSITES
-
(Not-set)
-
... borate phase Al18B4O33 (6 vol. %) forms during sintering, hindering densification. Porosity reaches 8 %, mass loss – 24 %, flexural strength – 300 MPa, fracture toughness – 4.2 MPa·m1/2. The introduction ...
-
12.
POWDER AND VOID. EXPERIENCE IN USING TWO-PRODUCT TRIBOKINETIKA MILLS IN THE PRODUCTION OF GROUND CHAMOTTE POWDER WITH IMPROVED PARTICLE SIZE DISTRIBUTION
-
(Not-set)
-
... fine fraction, 66.7 % granular fraction) exhibits porosity below 15 % (compaction coefficient 0.85). Energy consumption is 22.8 kWh per tonne of finished product. The economic feasibility of using two-product ...
-
13.
THE EFFECT OF ZIRCONIUM DIOXIDE NANOPARTICLES ON THE PROPERTIES OF CORUNDUM CERAMICS BASED ON RUSSIAN RAW MATERIALS
-
(Not-set)
-
The effect of various concentrations of zirconium dioxide nanoparticles on the strength and porosity of corundum ceramics obtained from domestic raw materials has been studied. The effect of an additive ...
-
14.
STUDY OF THE INFLUENCE OF DIFFERENT TEMPORARY TECHNOLOGICAL BINDERS ON CERAMICS VK94-1
-
(Not-set)
-
... porosity and linear shrinkage of the samples. Ceramics obtained using 8 wt. % PEG as a binder showed the best results compared to the material molded using 5 wt. % PVA. This is due to the fact that polyethylene ...
-
15.
DEVELOPMENT OF NANOMODIFIED CEMENT USING MICROSILICA, POLYCARBOXYLATE AND DUNE SAND: OPTIMIZATION OF COMPOSITION AND STRENGTH CHARACTERISTICS
-
(Not-set)
-
... ensures dense microstructure and maximum strength, while higher W/C values lead to increased porosity and strength loss. The findings highlight the potential of nanomodified cement technology for reducing ...
-
16.
EFFECT OF CeO2 ON THE STRUCTURE AND PROPERTIES OF ALUMINA-ZIRCONIA CERAMICS PREPARED BY PRESSURELESS SINTERING AND HOT PRESSING
-
(Not-set)
-
... by XRD and EDS. Pressureless sintering led to the stabilization of the cubic ZrO2 phase (c-ZrO2). Hot pressing achieved high relative density (>99 %) and practically no open porosity, while pressureless ...
-
17.
SINTERING OF Mg2TiO4 CERAMICS OBTAINED BY THE METHOD OF MECHANOCHEMICAL ACTIVATION OF A MIXTURE OF INITIAL POWDERS
-
(Not-set)
-
... is calculated using a non-isothermal method. The effect of increasing the firing temperature from 1300 to 1400 ?C on the density and porosity, as well as its microstructure of ceramics was studied. Ceramics ...
-
18.
STUDY OF CHARACTERISTICS OF ADHESIVE PERMANENT JOINTS IN REACTION-SINTERED CERAMIC MATERIALS BASED ON SILICON CARBIDE
-
(Not-set)
-
Laboratory samples of reaction-sintered silicon carbide ceramics with permanent adhesive joints were obtained based on isopropyl alcohol and phenol-formaldehyde resin solutions with different contents ...
-
19.
POROUS STRUCTURE OF A COMPOSITE MATERIAL BASED ON CORUNDUM AND GLASS
-
(Not-set)
-
... For samples of composites with an open porosity of 36…50 %, the size of the pore channels was estimated using capillary porometry. The correlation between the average pore size and the granulometric composition ...
-
20.
ON HIGH-TECH APPLICATIONS OF ZIRCONIUM DIOXIDE, PARTIALLY STABILIZED WITH YTTRIUM OXIDE (REVIEW)
-
(Not-set)
-
An overview of the applications of zirconium dioxide, partially stabilized with yttrium oxide, in various high-tech fields is presented. Particular attention is paid to its use in supercapacitors, where ...