-
21.
The systematic approach to controlling the technological process of glass production
-
(Science for glass production)
-
A systematic approach to managing the technological process of sheet glass production is presented, which comprehensively solves the problems of managing the quality of the produced glass, economical use ...
-
22.
Marnetic separation of raw materials for glass and ceramics production. Aspects of ferrous impurities control
-
(Raw materials)
-
... content of ferrous impurities); an unsystematic scatter of these data is revealed. It was stated that the results of traditional control (in terms of the "single" form of Fe 2 O 3 impurities), ...
-
23.
Control of a float glass annealing
-
(Efficiency and quality)
-
Models based on neural networks, describing the process of annealing a moving strip of sheet glass in a tunnel oven, have been developed. The problem of annealing temperature control is formulated. Simulation ...
-
24.
The effect of multicolored cullet on a tendency of container glass to frothing
-
(Science for glass production)
-
The tendency of container glass obtained from a mixture of green cullet with 10 - 50% colorless or brown to foaming has been estimated. An indirect method was used, which consists in controlling the apparent ...
-
25.
The effect of the redox potential on the susceptibility of glass to bubble nucleation
-
(Science for glass production)
-
The processes of glass clarification are closely related to its redox potential, for the quantitative assessment of which an indicator indicator was used - the proportion of ferrous iron, proportional ...
-
26.
Special features of the surface quality control upon mechanical treatment of glass ceramics
-
(Upgrading of quality)
-
The results of studies of diamond grinding of glass ceramics are presented. A technological system for diamond flat grinding of parts made of brittle non-metallic materials has been obtained. The factors ...
-
27.
Prospects of increasing power and ecological effectiveness of ceramic production
-
(Science for ceramic production)
-
Prospects for the use of reference materials on the best available technologies produced by the sectoral technical working groups of the European Bureau for Integrated Pollution Prevention and Control ...
-
28.
Ultrasonic control of strain behavior of thermoplastic slips
-
(Science for ceramic production)
-
The effect of ultrasound on the deformation properties of thermoplastic slips has been studied. It is shown that, upon sonication, the change in the plastic strength of casting systems beryllium oxide ...
-
29.
The effect of fluxing ingredient DULAPIX Ca on the flow property of majolica slip
-
(Science for ceramic production)
-
... on the hardness of the water: the higher its hardness, the higher the electrolyte content in the slip. Therefore, in the production of majolica slip, it is necessary to control the water hardness and use ...
-
30.
Using of simulation for quality control of the glass yield
-
(Quality and management)
-
Mathematical models of the sheet glass production process have been developed. The task of controlling the cooking-working process is formulated. The effectiveness of the use of mathematical models for ...
-
31.
Cause-effect relation of the spoilage upon brick firing in tunnel kilns
-
(At the enterprises and institutes)
-
Cause-and-effect relationships have been investigated when bricks are fired in tunnel kilns, and the reasons for rejects caused by the high-speed mode of heat treatment of products in the kiln have been ...
-
32.
Control of the properties of molding compounds developed on the base of technical alumina
-
(Science for ceramic production)
-
The influence of the amount of paraffin and the method of its introduction into the molding mass (after dispersion and joint dispersion), prepared from technical alumina and 20% nitric acid, has been investigated. ...
-
33.
The effect of additives and admixtures in tin on oxidation and incorporation of tin into bottom surface of the float glass
-
(Science for glass production)
-
Based on the analysis of patent information, scientific and technical literature and developments of the Saratov Institute of Glass, the influence of additives and impurities in tin on the quality of float ...
-
34.
Control of the stress-strain state of building glass stone
-
(Science for glass production)
-
On the basis of the polariscope-polarimeter, a device has been developed for monitoring residual stresses in building glass blocks, which makes it possible to automate the process of measuring residual ...
-
35.
The effect of gas-medium on the glass surface crystallization
-
(Science for glass production)
-
The possibility of changing the surface properties of sitalls by crystallizing glass in a controlled gas environment is shown. The main gas reagents and their action in the process of glass heat treatment ...
-
36.
Ceramic Quality Control
-
(Problems of quality)
-
Possible approaches to solving the problem of reproducibility of the quality of products made of ceramic materials are analyzed. It is indicated that only statistical methods are used for this purpose ...
-
37.
FABRICATION OF INTERPOSER SUBSTRATES BY LASER CUTTING AND LASER DRILLING
-
(Not-set)
-
... pulses and cutting by controlled thermal cleavage using a CO2 laser. In the experiments, the energy and number of pulse bursts, the beam waist position, as well as the CO2 laser parameters and the number ...
-
38.
PRODUCTION OF MICRONEEDLE ZIRCONIUM DIOXIDE POWDER STABILIZED BY ITTRIUM AND CERIUM
-
(Not-set)
-
The process of obtaining microneedle powdered ZrO2 from an aqueous solution of zirconium oxychloride, as well as zirconium dioxide doped with Y2O3 and CeO2 oxides, has been studied. Their chemical and ...
-
39.
ELECTRON-BEAM POWDER SURFACING OF Al2O3 ONTO TITANIUM IN THE FORE-VACUUM PRESSURE RANGE WITH PRELIMINARY POWDER DEGASSING
-
(Not-set)
-
The results of producing an Al2O3 composite coating on titanium by electron-beam cladding in the forevacuum pressure range (3…30 Pa) are presented. The microstructure, phase composition, and mechanical ...
-
40.
ELECTRON BEAM SINTERING OF ALUMINA-BASED COMPOSITE CERAMICS WITH COPPER ADDITION IN THE FORE-VACUUM PRESSURE RANGE
-
(Not-set)
-
The effect of electron-beam sintering in the fore-vacuum pressure range (8…10 Pa) on the density, structure, and phase composition of the sintered Al2O3–Cu composite with a component mass ratio of 10:1 ...