-
21.
INFLUENCE OF CONDITIONS AND MODES OF MIXTURE PREPARATION ON THE STRUCTURE AND STRENGTH OF SULFUR CONCRETE
-
(Not-set)
-
... The determination of the compressive strength of sulfur-concrete samples was carried out on an IP-1A-1000 test machine, structural studies of samples were carried out on a JEOL JSM-6480LV high-resolution ...
-
22.
ON HIGH-TECH APPLICATIONS OF ZIRCONIUM DIOXIDE, PARTIALLY STABILIZED WITH YTTRIUM OXIDE (REVIEW)
-
(Not-set)
-
An overview of the applications of zirconium dioxide, partially stabilized with yttrium oxide, in various high-tech fields is presented. Particular attention is paid to its use in supercapacitors, where ...
-
23.
CERAMICS WITH ULTRAHIGH PERMITTIVITY VALUES: COMPOSITIONS, SYNTHESIS METHODS AND PROPERTIES AT LOW AND MEDIUM FREQUENCIES
-
(Not-set)
-
An overview of dielectric materials with high (more than 10 000) values of relative permittivity is presented. Most of the compositions of these materials are based on systems that include ferroelectric ...
-
24.
INFLUENCE OF REFRACTORY FILLERS ON THE PROPERTIES OF CERAMICS BASED ON HIGH CONCENTRATED SILICA GLASS SUSPENSIONS
-
(Not-set)
-
Refractory and heat-resistant materials with a coarse-grained and large-porous structure were obtained using silica glass suspensions with mullite, spinel, corundum and quartz fillers. The influence of ...
-
25.
Glass Layer Forming in Ceramic Matrix Composite after Impact of High-Enthalpy Flow
-
(Not-set)
-
The structure of the surface layer of ceramic composite materials (CMC) of the compositions HfB 2 & # 8211; SiC and SiC & # 8211; TiC after exposure to a flow of dissociated air has been investigated. ...
-
26.
Investigation of the Adhesion Strength of Reactive Coatings on VZh171 Alloy by Sclerometry Method
-
(Not-set)
-
... for the occurrence of cracks in the pavement has been determined. The values ??obtained are high for this type of material and correspond to the level typical for chrome and nickel coatings. The results ...
-
27.
Obtaining of High-Porous Ceramic Materials on the Basis of Alumina-Magnesia Spinel
-
(Not-set)
-
The object of research is ceramic foam materials based on aluminum oxide, magnesium oxide and aluminum-magnesia spinel. The results of research on sintering spinel ceramics using aluminum and magnesium ...
-
28.
The Influence of Molarity and Temperature of the Alkaline Activator Solution on the Rheological Properties and Structure Formation of Alkaline Activated Refractory
Materials
-
(Not-set)
-
The effect of molarity (from 3.64 to 1.74 M) of a solution of an alkaline activator (ALA) and temperature (from 10 to 20 ° C) of a mixture of alkali-activated materials (ALA) based on chamotte and metakaolin ...
-
29.
New construction materials with enhanced strength based on met-als industrial waste
-
(Utilization of waste)
-
Non-firing and firing high-silica composite materials for construction purposes based on quartz sand and blast-furnace slag, which are characterized by increased strength and durability, high density, ...
-
30.
Thermal performance of diatomite-based materials in a broad temperature range
-
(Coatings)
-
... - 500 & # 176; C exceeds the strength values ??under normal conditions by about 2 times. This makes it possible to streamline the process of heating diatomite-based lining of high-temperature aggregat ...
-
31.
Changes in phase composition and strength of Al2O3-ZrO2 ce-ramics after hydrothermal ageing
-
(Biomaterials)
-
The influence of the mass content of Al 2 O 3 on the stability of the phase composition and the strength of the ceramics of the Al 2 O 3 -3Y system has been determined. -ZrO 2 prepared according ...
-
32.
Continuous strength of dense polycrystalline magnesia ceramics up to 1600 °С
-
(Science for ceramic production)
-
Experimental data on determining the long-term strength (time and deformation to fracture) of half-sintered periclase ceramics at temperatures up to 1600 ° C at loads of 20 - 50 MPa are presented. It is ...
-
33.
Optimisation of technological parameters for high-silica liquid glass construction materials synthesis
-
(Efficiency and quality)
-
... humidity conditions for the hardening of the compositions, the dispersion of the filler, the type and amount of the modifying additive, the quantitative ratio of the components of the raw mixture. High-silica ...
-
34.
Features of creep in polycrystal oxide ceramics at a temperature below 1600°C
-
(Science for ceramic production)
-
The results of studying the creep of polycrystalline ceramics based on metal oxides at temperatures up to 1600 ° C and high loads are presented. These temperatures are in the vicinity of the transition ...
-
35.
Features of deformation and fracture of polycrystalline oxide ceramics at temperatures up to 1600 °C
-
(Science for ceramic production)
-
... presence of nonequilibrium defects and stress concentrators, which were "hardened" during the cooling process after high-temperature firing during the preparation of materials. Destruction occurs, ...
-
36.
Low-temperature synthesis of the quenched cullet from the silica-based batch in production of foam materials
-
(Science for glass production)
-
The possibility of obtaining glass granulate as an intermediate product for glass-ceramic foam materials based on widespread silica components (marshallite, diatomite, flask) at temperatures not exceeding ...
-
37.
EFFECT OF TECHNOLOGICAL SYNTHESIS PARAMETERS ON THE STRUCTURE, PHASE COMPOSITION, AND PROPERTIES OF POROUS Al2O3–MgO–SiO2–SiC CERAMICS
-
(Not-set)
-
... in the compaction pressure from 20 to 40 MPa provides a twofold strengthening effect while maintaining high porosity, gas permeability, and structural homogeneity. The obtained results demonstrate the ...
-
38.
INVESTIGATION OF PHASE TRANSFORMATION ASPECTS IN THE REACTIVE SINTERING OF ZIRCONIUM DIBORIDE AND ZIRCONIUM CARBIDE
-
(Not-set)
-
Reactive sintering (siliconizing) at 1550?°C was employed to produce composite materials in the SiC–ZrB2 and SiC–ZrC systems. The influence of the initial zirconium compound on phase transformations, microstructure, ...
-
39.
OPTIMIZATION OF GEL-BASED 3D PRINTING TECHNOLOGY FOR BIOCOMPATIBLE CERAMIC IMPLANTS USING THE LINEAR ADVANCE FUNCTION
-
(Not-set)
-
The aim of this work was to optimize gel-based 3D printing technology for biocompatible ce-ramic implants based on an agar-agar–gelatin–brushite composition by applying the Linear Advance function – a ...
-
40.
PRODUCTION OF MICRONEEDLE ZIRCONIUM DIOXIDE POWDER STABILIZED BY ITTRIUM AND CERIUM
-
(Not-set)
-
The process of obtaining microneedle powdered ZrO2 from an aqueous solution of zirconium oxychloride, as well as zirconium dioxide doped with Y2O3 and CeO2 oxides, has been studied. Their chemical and ...